Dry Fog Dust Control Nozzles | FP Series
FP-10 Dry fog nozzles is intended for use in large, high capacity material handling applications where significant kinetic energy is needed to project high volumes of fog through large spaces. Nozzles are generally used in clusters as seen in the photos.
The geometry of the air passage causes the creation of high frequency, inaudible sound waves that are
reflected by the “resonator” creating a standing wave of acoustic energy. This energy shatters the flow of liquid. Although the nozzle is operated at air pressures from 30 – 60 psig (2-4 bar), the static pressure at the point of liquid injection is relatively constant near zero. This gives the nozzle the unique ability to adjust the pressure of one component without a significant effect on the flow of the other.
FP-10 Options and Components
The base version of the FP-10 is constructed of 304 SS and is used in non-abrasive applications.
For abrasive applications this version is constructed of 17/4 PH SS with TiCN wear coating. For protection from mechanical damage this version offers robust design but sacrifices fog quality.
For extreme abrasion applications this robust model offers a ruby resonator.
For mechanical protection of our standard nozzles and other brands we offer a slip on appliance.
Replacement 303 SS wire resonators and orifices for FP-10 nozzles are available along with replacement orifice/stem and O-rings are readily available.
FP-1 and FP-2 dry fog nozzles are intended for use in small, low capacity applications where very little kinetic energy is needed and low energy consumption is important. Nozzles are generally used in clusters as seen in the photos.
The geometry of the air passage causes the creation of high frequency, inaudible sound waves
that are reflected by the “resonator” creating a standing wave of acoustic energy. This energy shatters the flow of liquid. Although the nozzle is operated at air pressures from 30 – 60 psig (2-4 bar), the static pressure at the point of liquid injection is relatively constant near zero. This gives the nozzle the unique ability to adjust the pressure of one component without a significant effect on the flow of the other.
FP-1 and FP-2 Options and Components
The lowest flow version of the FP series is the FP-1. It carries little kinetic energy and is intended for use in small or quiescent environments.
The FP-2 has about twice the capacity of the FP-1 and consumes twice the compressed air. Both are available in two, three, or 4 piece design and with an abrasion resistant TiCN coated resonator.
Replacement parts and O-rings are readily available.
For more information on our range of Dry Fog Dust Control Nozzles please contact us.
To contact Dust Management Services about Dry Fog Dust Control Nozzles | FP Series use Get a quote.
FP-10 Dry fog nozzles is intended for use in large, high capacity material handling applications where significant kinetic energy is needed to project high volumes of fog through large spaces. Nozzles are generally used in clusters as seen in the photos.
The geometry of the air passage causes the creation of high frequency, inaudible sound waves that are
reflected by the “resonator” creating a standing wave of acoustic energy. This energy shatters the flow of liquid. Although the nozzle is operated at air pressures from 30 – 60 psig (2-4 bar), the static pressure at the point of liquid injection is relatively constant near zero. This gives the nozzle the unique ability to adjust the pressure of one component without a significant effect on the flow of the other.
FP-10 Options and Components
The base version of the FP-10 is constructed of 304 SS and is used in non-abrasive applications.
For abrasive applications this version is constructed of 17/4 PH SS with TiCN wear coating. For protection from mechanical damage this version offers robust design but sacrifices fog quality.
For extreme abrasion applications this robust model offers a ruby resonator.
For mechanical protection of our standard nozzles and other brands we offer a slip on appliance.
Replacement 303 SS wire resonators and orifices for FP-10 nozzles are available along with replacement orifice/stem and O-rings are readily available.
FP-1 and FP-2 dry fog nozzles are intended for use in small, low capacity applications where very little kinetic energy is needed and low energy consumption is important. Nozzles are generally used in clusters as seen in the photos.
The geometry of the air passage causes the creation of high frequency, inaudible sound waves
that are reflected by the “resonator” creating a standing wave of acoustic energy. This energy shatters the flow of liquid. Although the nozzle is operated at air pressures from 30 – 60 psig (2-4 bar), the static pressure at the point of liquid injection is relatively constant near zero. This gives the nozzle the unique ability to adjust the pressure of one component without a significant effect on the flow of the other.
FP-1 and FP-2 Options and Components
The lowest flow version of the FP series is the FP-1. It carries little kinetic energy and is intended for use in small or quiescent environments.
The FP-2 has about twice the capacity of the FP-1 and consumes twice the compressed air. Both are available in two, three, or 4 piece design and with an abrasion resistant TiCN coated resonator.
Replacement parts and O-rings are readily available.
For more information on our range of Dry Fog Dust Control Nozzles please contact us.
To contact Dust Management Services about Dry Fog Dust Control Nozzles | FP Series use Get a quote.
Thanks for your help!
Sorry! Unable to submit your request at this time. Please try again later.
Report this product