HT Oxygen Probe - High Temperature For ...

HT Oxygen Probe - High Temperature For Use Over 1000°C

Supplier: Ceramic Oxide Fabricators (Australia)

The HT Oxygen Probe is suitable for use at high temperatures over 1000°C such as in a kiln or furnace.

447 Recent Views In Stock

All of the Oxygen Probe components exposed to the high temperature gases are ceramic or platinum, for optimum corrosion resistance. It is of robust construction, with an alumina ceramic sheath to protect the sensing element.

Installation

The probe can be installed anywhere in the kiln or furnace, provided that the temperature at the tip is between 600°C and 1700°C. The probe will measure the oxygen concentration at the probe tip.

The port for installation should be sealed sufficiently to avoid atmospheric air from flowing inwards and causing a local variation in the oxygen concentration.

The probe can be used at any orientation for temperatures up to 1200°C, but should hang vertically if used at higher temperatures.

Connections

The probe head should be maintained at a temperature less than 60°C.

Clean respirable reference air at a rate of 10 cm3/min must be supplied to the connection provided on the probe head.

Features

Specific for O₂
High O₂ sensitivity and selectivity
High dynamic range of detection
High temperature of operation
Rapid responses
In situ measurement
Solid state electronic component – rugged sensor
No power consumed for operation under all conditions
No bias required to operate
Available up to 1400 mm

Applications

Fuel combustion efficiency control
Furnace gas analysis
Waste management systems
Temperature and oxygen control of kilns
Carburising (heat treating) furnace control
Potters’ kilns
Annealing furnaces
Large and small electric kilns
Flue gas analysis
O2 levels at high temperatures
CO2 harsh environments
Technical ceramic kiln systems
Industrial applications
Metal heat treatment processes
Molten systems (single use only)
Copper reverberator

For further information or a price quotation, please call or use the IndustrySearch enquiry box for a direct reply

To contact Ceramic Oxide Fabricators (Australia) about HT Oxygen Probe - High Temperature For Use Over 1000°C use Get a quote.

Installation

The probe can be installed anywhere in the kiln or furnace, provided that the temperature at the tip is between 600°C and 1700°C. The probe will measure the oxygen concentration at the probe tip.

The port for installation should be sealed sufficiently to avoid atmospheric air from flowing inwards and causing a local variation in the oxygen concentration.

The probe can be used at any orientation for temperatures up to 1200°C, but should hang vertically if used at higher temperatures.

Connections

The probe head should be maintained at a temperature less than 60°C.

Clean respirable reference air at a rate of 10 cm3/min must be supplied to the connection provided on the probe head.

Features

Specific for O₂
High O₂ sensitivity and selectivity
High dynamic range of detection
High temperature of operation
Rapid responses
In situ measurement
Solid state electronic component – rugged sensor
No power consumed for operation under all conditions
No bias required to operate
Available up to 1400 mm

Applications

Fuel combustion efficiency control
Furnace gas analysis
Waste management systems
Temperature and oxygen control of kilns
Carburising (heat treating) furnace control
Potters’ kilns
Annealing furnaces
Large and small electric kilns
Flue gas analysis
O2 levels at high temperatures
CO2 harsh environments
Technical ceramic kiln systems
Industrial applications
Metal heat treatment processes
Molten systems (single use only)
Copper reverberator

For further information or a price quotation, please call or use the IndustrySearch enquiry box for a direct reply

Read less...

To contact Ceramic Oxide Fabricators (Australia) about HT Oxygen Probe - High Temperature For Use Over 1000°C use Get a quote.

Let Ceramic Oxide Fabricators (Australia) provide you with a quote

Supplier

Get a quote

Supplier: Ceramic Oxide Fabricators (Australia)

Distribution: WorldWide

Location: Eaglehawk, VIC

Customers: Ceramic Components,Heat Treatment,Furnace Control

Trade With Confidence. The supplier of this item is approved as a Verified Supplier. Business registration, contact details and locations have been verified. Ceramic Oxide Fabricators (Australia) are also proudly displaying these credentials:

Established:

1976

Employees:

6-20

Customers:

Ceramic Components,Heat Treatment,Furnace Control

Memberships:

Australasian Ceramics Society

Certifications:

ISO 9001

Distribution:

WorldWide